初始過程流程^D
初始过程流程图 工序名称：装磁瓦 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |按检验卡片进行机壳总成、磁瓦、弹涨片 | | | | | |进料检验 | | | | | | | | | | | |存放在原材料仓库 | | | | | | | | | | | |从仓库领料至车间 | | | | | | | | | | | |取四片弹涨片，扣在工装的四个活动滑块 | | | | | |上 | | | | | | | | | | | |取四片磁瓦，磁瓦上的槽与工装上定位块 | | | | | |相吻合吸附在工装的四个弧形吸附块上 | | | | | | | | | | | |取一机壳总成，固定翼板上的螺钉尖向下 | |气压0.3-0.| | | |套于工装上，机壳缝与工装上的定位块方 | |5MPa | | | |向一致安装到位； | | | | | | | | | | | |踩下脚踏开关 | | | | | | | | | | | |自检 | | | | | | | | | | | |质保部抽检 | | | | | | | | | | | |将零件存放物料箱 | | | |编 制 | |审 核 | |批 准 | | 初始过程流程图 工序名称：拉铆 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |按检验卡片进行拉铆钉进料检验 | | | | | | | | | | | |存放在原材料仓库 | | | | | | | | | | | |从仓库领料至车间 | | | | | | | | | | | |取四个拉铆钉，分别插入机壳与弹涨片的 | | | | | |四个铆钉孔中； | | | | | | | | | | | |用拉铆枪一一完成拉铆过程 | | | | | | | | | | | |用吹尘枪吹干净机壳内部 | | | | | | | | | | | |自检 | |气压0.3-0.| | | | | |5MPa | | | |质保部抽检 | | | | | | | | | | | |将零件存放物料箱 | | | |编 制 | |审 核 | |批 准 | | 初始过程流程图 工序名称：充磁 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |将待充磁定子总成放入充磁头中 | | | | | | | | | | | | | | | | | |检查充磁电压为1.4KV | |充磁电压为| | | | | |1.4KV | | | | | | | | | |按下充磁开关进行充磁 | | | | | | | | | | | | | | | | | |测量磁通 |磁通大 | | | | | |于4.5 | | | | |自检 | | | | | | | | | | | |质保部抽检 | | | | | | | | | | | |将零件存放周转箱 | | | |编 制 | |审 核 | |批 准 | | 初始过程流程图 工序名称：上开口挡圈，装轴承 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |按检验卡片进行开口挡圈、轴承、电枢总 | | | | | |成进料检验 | | | | | | | | | | | |存放在原材料仓库 | | | | | | | | | | | |从仓库领料至车间 | | | | | | | | | | | |装开口挡圈 | | | | | | | | | | | |装前端轴承 | | | | | | | | | | | |装后端轴承 | | | | | | | | | | | |按下按钮 | |气压0.3-0.| | | | | |5MPa | | | |自检 | | | | | | | | | | | |质保部抽检 | | | | | | | | | | | |将零件放在传动板上流入下道 | | | |编 制 | |审 核 | |批 准 | | 初始过程流程图 工序名称：整机装配 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |按检验卡片进行前端盖、后端盖、波形垫 | | | | | |圈、电刷架总成进料检验 | | | | | | | | | | | |存放在原材料仓库 | | | | | | | | | | | |从仓库领料至车间 | | | | | | | | | | | |装电枢总成 | | | | | | | | | | | |装电刷架总成 | |气压0.4-0.| | | | | |6MPa | | | |装波形垫圈、后端盖 | | | | | | | | | | | |自检 | | | | | | | | | | | |质保部抽检 | | | | | | | | | | | |将零件放在传动板上流入下道 | | | |编 制 | |审 核 | |批 准 | | 初始过程流程图 工序名称：初测 |步骤 |装配 |领 |放 |检 |作业说明 |KPC |KCC | | | |料 |置 |验 | | | | | | |将电机卡在卡具上 | | | | | | | |气压0.1-0.| | | |线束插头与端子对接，按下按钮 | |2MPa | | | | | |时间8S | | | |测试 |无异声 | | |...
初始過程流程^D